隨著光伏發電系統快速發展,以及電動汽車充電樁的普及,傳統的剩余電流保護器無法滿足實際需求。介紹了一款B型剩余電流保護器,采用磁調制剩余電流互感器和零序電流互感器采集剩余電流。根據GB/T 22794—2017標準要求,可識別1 kHz及以下的正弦交流、帶和不帶直流分量的脈動直流、平滑直流等剩余電流信號。經信號調理電路將電壓信號送到單片機進行采集和判斷。通過試驗測試,該樣機在測試精度和速度上均符合國家標準的相關要求。The rapid development of photovoltaic power generation systems and the popularity of electric vehicle charging piles make the traditional residual current protective devices unable to meet the actual demand.This paper Proposed a type B residual current protective device,which uses the magnetically modulated residual current transformer and the zero sequence current transformer to acquire the residual current.According to the requirements of GB/T 22794—2017,the type B residual current protective device can detect sinusoidal AC residual current of 1kHz and below 1kHz,pulsating DC residual current with and without DC component,smooth DC residual current and so on.The signal processing circuit sends the voltage signal to the MCU for acquisition and judgment.Through experimental tests,the device meets the relevant requirements of national standards in terms of test accuracy and speed.
標簽：
電流保護器
上傳時間：
2022-03-27
上傳用戶：
鋰電池BMS管理技術是移動機器人的關鍵技術,本文設計了基于bq76PL455、STM32F103的鋰電池管理系統,實現了電池組電壓、電流、過壓、過流等狀態監測;系統配置均衡電路,電池充電過程中若出現電池單體電壓不平衡現象,會觸發均衡電路,進而提高電池的安全性,延長使用壽命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is Proposed to realize the monitoring of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
標簽：
移動機器人
鋰電池
bms管理系統
上傳時間：
2022-04-02
上傳用戶：
為適應雙向DC/DC功率變換的電流采樣需求,一種高精度高邊電流采樣電路被提出。其基本思想是在功率電路的高邊串入采樣電阻,借助電流鏡原理并引入偏置電流電路,將雙向電流均轉換為正向電壓輸出。通過理論分析與仿真結合的方法對電流鏡采樣原理及4種不同的偏置電流電路方案進行對比,最后通過實驗數據驗證了高精度高邊電流采樣電路的有效性。實驗數據表明,該采樣電路可在-25~75℃的溫度工作范圍內,針對-10~＋10 A范圍內的電流采樣實現優于5%的采樣精度。Current sensing plays an important role in controlling,monitoring or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is Proposed.The Proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the Proposed method.It is demonstrated that the Proposed current sensing circuit can achi...
標簽：
雙向DC電源
電流采樣
上傳時間：
2022-04-22
上傳用戶：
本文提出基于AD2S1210的旋變信號轉換電路,給出了具體的電路實現方法和配置方法.相比以往的RDC方案,本系統具有精度高,設計靈活,可靠性高等特點,可廣泛應用于各種伺服系統中.In this paper, the switching signal conversion circuit based on ADS1210 is Proposed, and the specific circuit implementation and configuration method are given. Compared with the previous RDC scheme, this system has the characteristics of high precision, flexible design and high reliability, and can be widely used in various servo systems.
標簽：
ad2s1210
上傳時間：
2022-05-04
上傳用戶：
數字頻率計是電工電子中常用的測量儀器,數字頻率計通過用輸入待測信號對一特定長度的信號進行計數,從而得出頻率并通過數碼管直觀的顯示出來。本文提出了一種與輸入同步的數字頻率計的設計,提高了頻率計的精度,設計采用Multisim軟件進行設計和仿真的過程,介紹了其工作原理,硬件電路設計和仿真的過程。設計采用了Multisim軟件進行設計和仿真,設計結果得到的驗證。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is Proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
標簽：
multisim
上傳時間：
2022-05-08
上傳用戶：
