Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上傳時間： 2013-11-08
上傳用戶：xianglee
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上傳時間： 2014-12-23
上傳用戶：eastimage
PCB 被動組件的隱藏特性解析 傳統上，EMC一直被視為「黑色魔術（black magic）」。其實，EMC是可以藉由數學公式來理解的。不過，縱使有數學分析方法可以利用，但那些數學方程式對實際的EMC電路設計而言，仍然太過復雜了。幸運的是，在大多數的實務工作中，工程師并不需要完全理解那些復雜的數學公式和存在于EMC規范中的學理依據，只要藉由簡單的數學模型，就能夠明白要如何達到EMC的要求。本文藉由簡單的數學公式和電磁理論，來說明在印刷電路板（PCB）上被動組件（passivecomponent）的隱藏行為和特性，這些都是工程師想讓所設計的電子產品通過EMC標準時，事先所必須具備的基本知識。導線和PCB走線導線（wire）、走線（trace）、固定架……等看似不起眼的組件，卻經常成為射頻能量的最佳發射器（亦即，EMI的來源）。每一種組件都具有電感，這包含硅芯片的焊線（bond wire）、以及電阻、電容、電感的接腳。每根導線或走線都包含有隱藏的寄生電容和電感。這些寄生性組件會影響導線的阻抗大小，而且對頻率很敏感。依據LC 的值（決定自共振頻率）和PCB走線的長度，在某組件和PCB走線之間，可以產生自共振（self-resonance），因此，形成一根有效率的輻射天線。在低頻時，導線大致上只具有電阻的特性。但在高頻時，導線就具有電感的特性。因為變成高頻后，會造成阻抗大小的變化，進而改變導線或PCB 走線與接地之間的EMC 設計，這時必需使用接地面（ground plane）和接地網格（ground grid）。導線和PCB 走線的最主要差別只在于，導線是圓形的，走線是長方形的。導線或走線的阻抗包含電阻R和感抗XL = 2πfL，在高頻時，此阻抗定義為Z = R + j XL j2πfL，沒有容抗Xc = 1/2πfC存在。頻率高于100 kHz以上時，感抗大于電阻，此時導線或走線不再是低電阻的連接線，而是電感。一般而言，在音頻以上工作的導線或走線應該視為電感，不能再看成電阻，而且可以是射頻天線。
上傳時間： 2013-10-09
上傳用戶：時代將軍
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上傳時間： 2013-11-18
上傳用戶：zhouxuepeng1
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上傳時間： 2014-01-18
上傳用戶：wenyuoo
The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
上傳時間： 2013-11-20
上傳用戶：ynzfm
Bootloader是微處理器上電時運行的第一段代碼，它可以通過通信接口實現對微處理器內部應用程序的更新升級，為網絡化嵌入式產品的應用程序升級帶來極大的便利。由于目前沒有統一嵌入式系統的Bootloader。基于NEC 78K0系列單片機自編程原理，設計出一個適用于78K0/Fx2系列單片機的Bootloader，并能夠通過單片機串口在線升級應用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
標簽： Bootloader MCU 自編程
上傳時間： 2013-10-26
上傳用戶：fang2010
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上傳時間： 2013-11-16
上傳用戶：浩子GG
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上傳時間： 2013-10-22
上傳用戶：taiyang250072
很多不同的廠家生產各種型號的計算機，它們運行完全不同的操作系統，但TCP.IP協議族允許它們互相進行通信。這一點很讓人感到吃驚，因為它的作用已遠遠超出了起初的設想。T C P / I P起源于6 0年代末美國政府資助的一個分組交換網絡研究項目，到9 0年代已發展成為計算機之間最常應用的組網形式。它是一個真正的開放系統，因為協議族的定義及其多種實現可以不用花錢或花很少的錢就可以公開地得到。它成為被稱作“全球互聯網”或“因特網(Internet)”的基礎，該廣域網（WA N）已包含超過1 0 0萬臺遍布世界各地的計算機。本章主要對T C P / I P協議族進行概述，其目的是為本書其余章節提供充分的背景知識。 TCP.IP協議 縮略語 ACK (ACKnowledgment) TCP首部中的確認標志 API (Application Programming Interface) 應用編程接口 ARP (Address Resolution Protocol) 地址解析協議 ARPANET(Defense Advanced Research Project Agency NETwork) (美國)國防部遠景研究規劃局 AS (Autonomous System) 自治系統 ASCII (American Standard Code for Information Interchange) 美國信息交換標準碼 ASN.1 (Abstract Syntax Notation One) 抽象語法記法1 BER (Basic Encoding Rule) 基本編碼規則 BGP (Border Gateway Protocol) 邊界網關協議 BIND (Berkeley Internet Name Domain) 伯克利I n t e r n e t域名 BOOTP (BOOTstrap Protocol) 引導程序協議 BPF (BSD Packet Filter) BSD 分組過濾器 CIDR (Classless InterDomain Routing) 無類型域間選路 CIX (Commercial Internet Exchange) 商業互聯網交換 CLNP (ConnectionLess Network Protocol) 無連接網絡協議 CRC (Cyclic Redundancy Check) 循環冗余檢驗 CSLIP (Compressed SLIP) 壓縮的S L I P CSMA (Carrier Sense Multiple Access) 載波偵聽多路存取 DCE (Data Circuit-terminating Equipment) 數據電路端接設備 DDN (Defense Data Network) 國防數據網 DF (Don’t Fragment) IP首部中的不分片標志 DHCP (Dynamic Host Configuration Protocol) 動態主機配置協議 DLPI (Data Link Provider Interface) 數據鏈路提供者接口 DNS (Domain Name System) 域名系統 DSAP (Destination Service Access Point) 目的服務訪問點 DSLAM (DSL Access Multiplexer) 數字用戶線接入復用器 DSSS (Direct Sequence Spread Spectrum) 直接序列擴頻 DTS (Distributed Time Service) 分布式時間服務 DVMRP (Distance Vector Multicast Routing Protocol) 距離向量多播選路協議 EBONE (European IP BackbONE) 歐洲I P主干網 EOL (End of Option List) 選項清單結束 EGP (External Gateway Protocol) 外部網關協議 EIA (Electronic Industries Association) 美國電子工業協會 FCS (Frame Check Sequence) 幀檢驗序列 FDDI (Fiber Distributed Data Interface) 光纖分布式數據接口 FIFO (First In, First Out) 先進先出 FIN (FINish) TCP首部中的結束標志 FQDN (Full Qualified Domain Name) 完全合格的域名 FTP (File Transfer Protocol) 文件傳送協議 HDLC (High-level Data Link Control) 高級數據鏈路控制 HELLO 選路協議 IAB (Internet Architecture Board) Internet體系結構委員會 IANA (Internet Assigned Numbers Authority) Internet號分配機構 ICMP (Internet Control Message Protocol) Internet控制報文協議 IDRP (InterDomain Routing Protocol) 域間選路協議 IEEE (Institute of Electrical and Electronics Engineering) （美國）電氣與電子工程師協會 IEN (Internet Experiment Notes) 互聯網試驗注釋 IESG (Internet Engineering Steering Group) Internet工程指導小組 IETF (Internet Engineering Task Force) Internet工程專門小組 IGMP (Internet Group Management Protocol) Internet組管理協議 IGP (Interior Gateway Protocol) 內部網關協議 IMAP (Internet Message Access Protocol) Internet報文存取協議 IP (Internet Protocol) 網際協議 I RTF (Internet Research Task Force) Internet研究專門小組 IS-IS (Intermediate System to Intermediate System Protocol) 中間系統到中間系統協議 ISN (Initial Sequence Number) 初始序號 ISO (International Organization for Standardization) 國際標準化組織 ISOC (Internet SOCiety) Internet協會 LAN (Local Area Network) 局域網 LBX (Low Bandwidth X) 低帶寬X LCP (Link Control Protocol) 鏈路控制協議 LFN (Long Fat Net) 長肥網絡 LIFO (Last In, First Out) 后進先出 LLC (Logical Link Control) 邏輯鏈路控制 LSRR (Loose Source and Record Route) 寬松的源站及記錄路由 MBONE (Multicast Backbone On the InterNEt) Internet上的多播主干網 MIB (Management Information Base) 管理信息庫 MILNET (MILitary NETwork) 軍用網 MIME (Multipurpose Internet Mail Extensions) 通用I n t e r n e t郵件擴充 MSL (Maximum Segment Lifetime) 報文段最大生存時間 MSS (Maximum Segment Size) 最大報文段長度 M TA (Message Transfer Agent) 報文傳送代理 MTU (Maximum Transmission Unit) 最大傳輸單元 NCP (Network Control Protocol) 網絡控制協議 NFS (Network File System) 網絡文件系統 NIC (Network Information Center) 網絡信息中心 NIT (Network Interface Tap) 網絡接口栓（S u n公司的一個程序） NNTP (Network News Transfer Protocol) 網絡新聞傳送協議 NOAO (National Optical Astronomy Observatories) 國家光學天文臺 NOP (No Operation) 無操作 NSFNET (National Science Foundation NETwork) 國家科學基金網絡 NSI (NASA Science Internet) （美國）國家宇航局I n t e r n e t NTP (Network Time Protocol) 網絡時間協議 NVT (Network Virtual Terminal) 網絡虛擬終端 OSF (Open Software Foudation) 開放軟件基金 OSI (Open Systems Interconnection) 開放系統互連 OSPF (Open Shortest Path First) 開放最短通路優先 PAWS (Protection Against Wrapped Sequence number) 防止回繞的序號 PDU (Protocol Data Unit) 協議數據單元 POSIX (Portable Operating System Interface) 可移植操作系統接口 PPP (Point-to-Point Protocol) 點對點協議 PSH (PuSH) TCP首部中的急迫標志 RARP (Reverse Address Resolution Protocol) 逆地址解析協議 RFC (Request For Comments) Internet的文檔，其中的少部分成為標準文檔 RIP (Routing Information Protocol) 路由信息協議 RPC (Remote Procedure Call) 遠程過程調用 RR (Resource Record) 資源記錄 RST (ReSeT) TCP首部中的復位標志 RTO (Retransmission Time Out) 重傳超時 RTT (Round-Trip Time) 往返時間 SACK (Selective ACKnowledgment) 有選擇的確認 SLIP (Serial Line Internet Protocol) 串行線路I n t e r n e t協議 SMI (Structure of Management Information) 管理信息結構 SMTP (Simple Mail Transfer Protocol) 簡單郵件傳送協議 SNMP (Simple Network Management Protocol) 簡單網絡管理協議 SSAP (Source Service Access Point) 源服務訪問點 SSRR (Strict Source and Record Route) 嚴格的源站及記錄路由 SWS (Silly Window Syndrome) 糊涂窗口綜合癥 SYN (SYNchronous) TCP首部中的同步序號標志 TCP (Transmission Control Protocol) 傳輸控制協議 TFTP (Trivial File Transfer Protocol) 簡單文件傳送協議 TLI (Transport Layer Interface) 運輸層接口 TTL (Ti m e - To-Live) 生存時間或壽命 TUBA (TCP and UDP with Bigger Addresses) 具有更長地址的T C P和U D P Telnet 遠程終端協議 UA (User Agent) 用戶代理 UDP (User Datagram Protocol) 用戶數據報協議 URG (URGent) TCP首部中的緊急指針標志 UTC (Coordinated Universal Time) 協調的統一時間 UUCP (Unix-to-Unix CoPy) Unix到U n i x的復制 WAN (Wide Area Network) 廣域網 WWW (World Wide Web) 萬維網 XDR (eXternal Data Representation) 外部數據表示 XID (transaction ID) 事務標識符 XTI (X/Open Transport Layer Interface) X/ O p e n運輸層接口
上傳時間： 2013-11-13
上傳用戶：tdyoung
