為提升虛擬儀器傳輸速率與實時性能，擴展監測范圍，在VC的軟件平臺上設計了一種全功能虛擬示波器。與傳統虛擬示波器相比，該系統采用嵌入式系統完成信號采集，采用工業以太網為傳輸介質，通過線性插值算法和多線程編程思想，實現波形顯示、參數計算、頻譜分析以及波形存儲及回放功能。實驗結果表明，該虛擬示波器可以實現20 kHz采樣頻率下的波形精確顯示，達到預期的各項指標。 Abstract: o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
上傳時間： 2013-11-25
上傳用戶：wbwyl
The field of microelectromechanical systems (MEMS), particularly micromachinedmechanical transducers, has been expanding over recent years, and the productioncosts of these devices continue to fall. Using materials, fabrication processes, anddesign tools originally developed for the microelectronic circuits industry, newtypes of microengineered device are evolving all the time—many offering numerousadvantages over their traditional counterparts. The electrical properties of siliconhave been well understood for many years, but it is the mechanical properties thathave been exploited in many examples of MEMS. This book may seem slightlyunusual in that it has four editors. However, since we all work together in this fieldwithin the School of Electronics and Computer Science at the University of Southampton,it seemed natural to work together on a project like this. MEMS are nowappearing as part of the syllabus for both undergraduate and postgraduate coursesat many universities, and we hope that this book will complement the teaching thatis taking place in this area.
上傳時間： 2013-10-16
上傳用戶：朗朗乾坤
User ManualRev. 1.2SmartRF® CC2420DK: Packet Sniffer for IEEE 802.15.4 and ZigBee Table of contents1 INTRODUCTION...............................................................................................31.1 HARDWARE PLATFORM.......................................................................................31.2 SOFTWARE.........................................................................................................32 USER INTERFACE..........................................................................................42.1 MENUS AND TOOLBARS.......................................................................................62.2 SETUP................................................................................................................62.3 SELECT FIELDS...................................................................................................72.3.1 Tips............................................................................................................72.4 PACKET DETAILS.................................................................................................72.5 ADDRESS BOOK..................................................................................................92.5.1 Tips............................................................................................................92.6 DISPLAY FILTER................................................................................................102.7 TIME LINE.........................................................................................................103 HELP....................................................................................................................114 TROUBLESHOOTING..................................................................................125 GENERAL INFORMATION........................................................................135.1 DOCUMENT HISTORY........................................................................................135.2 DISCLAIMER......................................................................................................135.3 TRADEMARKS...................................................................................................136 ADDRESS INFORMATION........................................................................14
上傳時間： 2014-01-14
上傳用戶：zhangyi99104144
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上傳時間： 2013-11-05
上傳用戶：Wwill
We all know the benefits of using FieldProgrammable Gate Arrays (FPGAs): no NRE, nominimum order quantities, and faster time-tomarket.In an ideal world, designs would never needto be changed because of design errors, but we allknow that sometimes this is necessary.
上傳時間： 2013-11-04
上傳用戶：leixinzhuo
The use of the Wind River VxWorks Real-Time Operating System (RTOS) on Virtex™-4embedded PowerPC™ processors continues to be a popular choice for high performanceFPGA designs. The introduction of the Wind River Workbench design environment has enableda new and easier way for designers to control the configuration of the VxWorks kernel. Thisguide shows the steps required to build and configure a ML403 Embedded DevelopmentPlatform to boot and run the VxWorks RTOS. A VxWorks bootloader is created, programmedinto Flash, and used to boot the design. The concepts presented here can be scaled to anyPowerPC enabled development platform.
上傳時間： 2013-10-26
上傳用戶：agent
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上傳時間： 2013-11-07
上傳用戶：swing
The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
上傳時間： 2013-11-12
上傳用戶：363186
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上傳時間： 2014-12-30
上傳用戶：aysyzxzm
