基于單片機的步進電機開環控制系統:通過ATMEL89C51單片機對步進電機進行控制,主要介紹了步進電機控制器、驅動電路和LED顯示電路的設計,實現了步進電機的開環控制。在步進電機控制器的設計中,重點闡述了脈沖產生電路以及對速度的控制。該系統具有成本低、控制方便的特點。關鍵詞: 單片機; 步進電機; 開環控制 Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the Speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
上傳時間： 2013-10-13
上傳用戶：cicizoe
這一顆，我們學習如何讓跑馬燈自動按照我們預定的順序進行。這種控制在工控場合經常用到。這個程序里，我們預先定義了一個變化的順序Speedcode，每跑一圈燈就根據預定設置的表格數據來決定下一圈的跑馬速度。這樣我們就實現了按照預定的順序自動變化運行。請看代碼：-----------------------------------#define uchar unsigned char //定義一下方便使用#define uint unsigned int#define ulong unsigned long#include <reg52.h> //包括一個52 標準內核的頭文件sbit P10 = P1^0; //頭文件中沒有定義的IO 就要自己來定義了sbit P11 = P1^1;sbit P12 = P1^2;sbit P13 = P1^3;bit ldelay=0; //長定時溢出標記,預置是0uchar Speed=10; //設置一個變量保存跑馬燈的移動速度uchar code Speedcode[10]={3,1,5,12,3,20,2,10,1,4}; //10 個預定義的速度char code dx516[3] _at_ 0x003b;//這是為了仿真設置的//可編程自動控制跑馬燈void main(void) // 主程序{uchar code ledp[4]={0xfe,0xfd,0xfb,0xf7};//預定的寫入P1 的值uchar ledi; //用來指示顯示順序uchar i;RCAP2H =0x10; //賦T2 的預置值0x1000，溢出30 次就是1 秒鐘RCAP2L =0x00;TR2=1; //啟動定時器ET2=1; //打開定時器2 中斷EA=1; //打開總中斷
上傳時間： 2013-11-20
上傳用戶：ming529
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum Speed of the interface. In addition,microcontrollers like the SAB C505 will Speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum Speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
標簽： synchronous Emulating serial
上傳時間： 2014-01-31
上傳用戶：z1191176801
針對運行中火車測速運用多普勒效應采用DSP 設計雷達測速系統并闡述了其基本設計思想與工作原理給出系統硬件軟件設計結構和原理圖改善了原有光電測速精度提高了系統工作穩定性和可靠性經實驗證明DSP 采集板工作穩定測速效果好關鍵詞DSP; 雷達測速; 多普勒效應 On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train Speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader Speed measurement; doppler principle
上傳時間： 2013-10-27
上傳用戶：003030
中文版詳情瀏覽：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system Speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
標簽： UltraScale Xilinx 架構
上傳時間： 2013-11-13
上傳用戶：瓦力瓦力hong
Consumer display applications commonly use high-Speed LVDS interfaces to transfer videodata. Spread-spectrum clocking can be used to address electromagnetic compatibility (EMC)issues within these consumer devices. This application note uses Spartan®-6 FPGAs togenerate spread-spectrum clocks using the DCM_CLKGEN primitive.
上傳時間： 2014-12-28
上傳用戶：yan2267246
波長信號的解調是實現光纖光柵傳感網絡的關鍵，基于現有的光纖光柵傳感器解調方法，提出一種基于FPGA的雙匹配光纖光柵解調方法，此系統是一種高速率、高精度、低成本的解調系統，并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計，綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-Speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing Speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上傳時間： 2014-07-24
上傳用戶：caiguoqing
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-Speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
標簽： Transceiver Virtex Wizar GTP
上傳時間： 2013-10-23
上傳用戶：leyesome
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-Speed data download mode for assembly line andservice data transfer operations. The high-Speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher Speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-Speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-Speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上傳時間： 2014-12-30
上傳用戶：aysyzxzm
