The MAX504/MAX515 are low-power, Voltage-output,
10-bit digital-to-analog converters (DACs) specified for
single +5V power-supply operation.用于DA轉(zhuǎn)換芯片選型
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, Voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
Abstract: This application note helps system designers choose the correct external components for use with the MAX16948 dualremote antenna LDO/switch, thus ensuring that automobile-regulated phantom antenna supply and output-current-monitoring circuitrymeet performance objectives. An electronic calculator is provided that helps specify the critical external components for theMAX16948, thus reducing design time. The calculator also determines the device's analog output voltage, output current-limitthreshold, and output current-sensing accuracies. The calculator includes new automatic Step By Step feature that assists designerswith component choice. To use the new automatic feature, click on the Step By Step button relative to the desired section.
12bit 低功耗DAC 數(shù)模轉(zhuǎn)換器
The MAX5302 combines a low-power, Voltage-output,
12-bit digital-to-analog converter (DAC) and a precision
output amplifier in an 8-pin μMAX package. It operates
from a single +5V supply, drawing less than 280μA of
supply current.
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
16 relay output channels and 16 isolated digital input channels
LED indicators to show activated relays
Jumper selectable Form A/Form B-type relay output channel
Output status read-back
Keep relay output values when hot system reset
High-voltage isolation on input channels(2,500 VDC)
Hi ESD protection(2,00VDC)
High over-voltage protection(70VDC)
Wide input range(10~50VDC)
Interrupt handling capability
High-density DB-62 connector
Board ID
電力電子環(huán)流SIMULINK模型 Notice that the Thyristor blocks have an output identified by the letter m. This output returns a Simulink vectorized signal containing the thyristor current (Iak) and voltage (Vak).
full wave rectifierDuring the period from 偽 to 蟺, the input voltage vs input current is are positive and the power flows from supply to the load. The converter is said to be operated at rectification mode .During the period from 蟺 to 蟺+偽 , the input voltage vs is negative and the input current is is positive and reverse power flows from load to the supply. The converter is said to be operated in inversion mode. Depending on the value of 偽, average output voltage can be either positive or negative and hence provides 2 quadrant operation.
