The 14-bit LTC2351-14 is a 1.5Msps, low power SARADC with six simultaneously sampled differential inputchannels. It operates from a single 3V supply and featuressix independent sample-and-hold amplifi ers and a singleADC. The single ADC with multiple S/HAs enables excellentrange match (1mV) between channels and channel-tochannelskew (200ps).
上傳時間： 2014-12-23
上傳用戶：天誠24
Many 8-bit and 16-bit microcontrollers feature 10-bitinternal ADCs. A few include 12-bit ADCs, but these oftenhave poor or nonexistent AC specifi cations, and certainlylack the performance to meet the needs of an increasingnumber of applications. The LTC®2366 and its slowerspeed versions offer a high performance alternative, asshown in the AC specifi cations in Table 1. Compare theseguaranteed specifi cations with the ADC built into yourcurrent microcontroller.
上傳時間： 2013-10-26
上傳用戶：jackandlee
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上傳時間： 2014-12-23
上傳用戶：eastimage
ADC制造商在數據手冊中定義ADC性能的方式令人困惑，并且可能會在應用開發中導致錯誤的推斷。最大的困惑也許就是“分辨率”和“精確度”了——即Resolution和Accuracy，這是兩個不同的參數，卻經常被混用，但事實上，分辨率并不能代表精確度，反之亦然。本文提出并解釋了ADC“分辨率”和“精確度”，它們與動態范圍、噪聲層的關系，以及在諸如計量等應用中的含義。
上傳時間： 2013-11-06
上傳用戶：gxrui1991
模擬轉換器性能不只依賴分辨率規格 大量的模數轉換器(ADC)使人們難以選擇最適合某種特定應用的ADC器件。工程師們選擇ADC時，通常只注重位數、信噪比(SNR)、諧波性能，但是其它規格也同樣重要。本文將介紹ADC器件最易受到忽視的九項規格，并說明它們是如何影響ADC性能的。 1. SNR比分辨率更為重要。 ADC規格中最常見的是所提供的分辨率，其實該規格并不能表明ADC器件的任何能力。但可以用位數n來計算ADC的理論SNR： 不 過工程師也許并不知道，熱噪聲、時鐘抖動、差分非線性(DNL)誤差以及其它參數異常都會限制ADC器件的SNR。對于高性能高分辨率轉換器尤其如此。一 些數據表提供有效位數(ENOB)規格，它描述了ADC器件所能提供的有效位數。為了計算ADC的ENOB值，應把測量的SNR值放入上述公式，并求解 n。
上傳時間： 2014-12-22
上傳用戶：z240529971
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
運行典型高速ADC評估板設置
上傳時間： 2013-10-22
上傳用戶：ly1994
采用高輸入頻率、高速模數轉換器(ADC)的系統設計是一項具挑戰性的任務。ADC輸入接口設計有6個主要條件：輸入阻抗、輸入驅動、帶寬、通帶平坦度、噪聲和失真。
上傳時間： 2013-10-21
上傳用戶：chukeey
atmage16單片機DAC范例程序
上傳時間： 2014-12-25
上傳用戶：hzy5825468
s3c2440a資料ADC和觸摸屏接口
上傳時間： 2014-10-13
上傳用戶：15070202241
<strike id="yqec6"></strike>