<strike id="ymooo"></strike>
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
FCMDEMO displays a GUI window to let you try out various parameters in fuzzy c-means clustering for 2-D data. You can choose the data set and clustering number from the GUI buttons at right, and then click "Start" to start the fuzzy clustering process.
標簽： clustering parameters displays FCMDEMO
上傳時間： 2014-01-23
上傳用戶：bjgaofei
Embest Arm EduKit II Evaluation Board External Interrupt Test Example Please Select the trigger: 1 - Falling trigger 2 - Rising trigger 3 - Both Edge trigger 4 - Low level trigger 5 - High level trigger any key to exit... Press the buttons push buttons may have glitch noise problem EINT6 had been occured... LED1 (D1204) on
標簽： Evaluation Interrupt External Example
上傳時間： 2015-10-08
上傳用戶：Altman
Spartan 3 Digilent Demo:This demo drives the perphrials on the Spartan 3 board. This drives a simple pattern to the VGA port, connects the switches to the LEDs, buttons to each anode of the seven segment decoder. The seven segment decoder has a simple counter running on it, and when SW0 is in the up position the seven segment decoder will display scan codes from the PS2 port. This demo how ever does not drive the RS-232 port or the memory. This is a simple design done entirely VHDL not microblaze.
標簽： Spartan drives This perphrials
上傳時間： 2014-05-29
上傳用戶：SimonQQ
this a pack include source code for quartus 2. It is an implementation of the LC2. The LC-2 computer is described in Introduction to Computing Systems from Bits & Gates to C & Beyond by Yale Patt and Sanjay Patel, McGraw Hill, 2001. The LC2 model can be run as a simulation or downloaded to the UP3 in a larger model, TOP_LC2 that adds video output. Push buttons reset and single step the processor and a video output display of registers is generated. This state machine VHDL-based model of the LC-2 includes all source files. Currently compiled for a Cyclone EP1C6Q240 FPGA.
標簽： implementation include quartus source
上傳時間： 2013-12-25
上傳用戶：壞壞的華仔
Floating Window.It is descendant of TCustomPanel. You can: - Drag on its title bar. - Set title bar on the left (only for truetype font) - Show/Hide buttons on title bar - Expand/shrink window (like tool window in CorelDraw)
標簽： title TCustomPanel descendant Floating
上傳時間： 2013-12-20
上傳用戶：wendy15
To use the ATLTrace tool: Debug an MFC or ATL project select Start from the Debug menu. Select MFC/ATL Trace Tool in the Tools menu. Expand the tree control list in the Trace List window. Here you will see the running application, any modules within that application, and the trace categories for each module. Customize, for each process, module, and category, which information is displayed in the output window. The Trace level control in the Process group is related to the ATLTRACE2 level only those ATLTRACE2 messages with a level equal to or greater than the setting in the Trace level control will be displayed in the output window. Select Apply to put your settings into effect. You can save your settings, and load them the next time you debug the application use the Save and Load buttons.
標簽： Debug the ATLTrace project
上傳時間： 2014-01-15
上傳用戶：wfl_yy
This application creates an USB HID (Human-Interface Device) keyboard on a host computer. Pressing any of the buttons on the board outputs characters or special keys on the host side
標簽： Human-Interface application Pressing computer
上傳時間： 2014-01-04
上傳用戶：曹云鵬
This Tetris-Clone was assembled from one ATmega8, 240 red LEDs, a few BJTs, a few IC s and some push-buttons.
標簽： Tetris-Clone assembled few ATmega
上傳時間： 2016-05-29
上傳用戶：ZJX5201314
一款支持Delphi和C++ Builder的VCL控件，可以幫助你創建類似Winamp那樣的具有Skins的程序。menus, buttons, trackbars, gauges, labels以及其他一些控件和對象都可以創建Skins 。Delphi 2005、Delphi 5,6,7和C++ Builder 5,6 均適用。
上傳時間： 2016-06-25
上傳用戶：李夢晗
