The WCDMA Physical Layer Demo consists of an end-to-end (transmitter-to-receiver) simulation of the frequency Division Duplex (FDD) Downlink physical layer for several Dedicated Channels (DCH) as specified by the 3GPP standard (Release 99).
MSP-FET430P410 Demo - Timer_A Toggle P5.1, CCR0 Contmode ISR, DCO SMCLK
Description Toggle P5.1 using using software and TA_0 ISR. Toggle rate is
set at 50000 DCO/SMCLK cycles. Default DCO frequency used for TACLK.
Durring the TA_0 ISR P5.1 is toggled and 50000 clock cycles are added to CCR0. TA_0 ISR is triggered exactly 50000 cycles. CPU is normally off and
used only durring TA_ISR.
ACLK = n/a, MCLK = SMCLK = TACLK = DCO ~ 800k
The purpose of this document is to present how to use the Timer for the generation of a PWM signal tunable in frequency and duty cycle. As an application example, this document is based on a basic “music” synthesizer through an external buzzer. Example code is also available in the it.
Circular Convolution of two equal-length vectors. Highlights that circular convolution in the time domain is the effectively the same as element-by-element multiplication in the frequency domain.
WB_BPSK_Analysis.rar:BPSK modulation and link analysis of UWB monocycle and doublet waveforms.Revised 1/2/05-JC.This m file plots the time and frequency waveforms for BPSK 1st and 2nd derivative equations used in UWB system analysis.
MATLAB Code for Optimal Quincunx Filter
Bank Design
Yi Chen
July 17, 2006
This file introduces the MATLAB code that implements the two algorithms (i.e., Algorithms
1 and 2 in [1], or Algorithms 4.1 and 4.2 in [2]) used for the construction of
quincunx filter banks with perfect reconstruction, linear phase, high coding gain, certain
vanishing moments properties, and good frequency selectivity. The code can be
used to design quincunx filter banks with two, three, or four lifting steps. The SeDuMi
Matlab toolbox [3] is used to solve the second-order cone programming subproblems
in the two algorithms, and must be installed in order for this code to work.
DDR SDRAM控制器的VHDL源代碼，含詳細(xì)設(shè)計(jì)文檔。
The DDR, DCM, and SelectI/O™ features in the Virtex™ -II architecture make it the perfect
choice for implementing a controller of a Double Data Rate (DDR) SDRAM. The Digital Clock
Manager (DCM) provides the required Delay Locked Loop (DLL), Digital Phase Shift (DPS),
and Digital frequency Synthesis (DFS) functions. This application note describes a controller
design for a 16-bit DDR SDRAM. The application note and reference design are enhanced
versions of XAPP200 targeted to the Virtex-II series of FPGAs. At a clock rate of 133 MHz,
16-bit data changes at both clock edges. The reference design is fully synthesizable and
achieves 133 MHz performance with automatic place and route tools.
*** *** *** *** *** *** *****
** Two wire/I2C Bus READ/WRITE Sample Routines of Microchip s
** 24Cxx / 85Cxx serial CMOS EEPROM interfacing to a
** PIC16C54 8-bit CMOS single chip microcomputer
** Revsied Version 2.0 (4/2/92).
**
** Part use = PIC16C54-XT/JW
** Note: 1) All timings are based on a reference crystal frequency of 2MHz
** which is equivalent to an instruction cycle time of 2 usec.
** 2) Address and literal values are read in octal unless otherwise
** specified.
