集合式直流電能表（小功率的） 特點： 精確度0.05%滿刻度±1位數 可同時量測與顯示/直流電壓/電流/瓦特（千瓦）/瓦特小時（千瓦小時） 電壓輸入（DC0-99.99V/0-600.0V）自動變檔功能 顯示范圍0-9999(電流/瓦特/千瓦),0至99999999(八位數瓦特小時)可任意規劃 數位RS-485 界面 (Optional) 主要規格： 輔助電源消耗功率：＜0.35VA(DC12V/DC24V) ＜0.5VA（DC48V） ＜1.5VA（AC90-240V(50/60Hz)） 精確度: 0.05% F.S. ±1 digit (23 ±5℃) 輸入范圍：Auto range(DC0-99.99V/0-600.0V(DC voltage)) 輸入抗阻：＞5MΩ（DC voltage） 取樣時間：10 cycles/second(total) 過載顯示: " doFL " 顯示值范圍: 0-9999 digit（DCA/W(KW)） 0-9999999.999 digit(WH/(KWH)) RS-485傳輸速度: 19200/9600/4800/2400 selective RS-485通訊位址: "01"-"FF"（0-255） RS-485通信協議: Modbus RTU mode 溫度系數: 50ppm/℃ (0-50℃) 顯示幕:Bight Red LEDs high 10.16 mm(0.4") 參數設定方式: Touch switches 記憶方式: Non-volatile E²PROM memory 絕緣耐壓能力:2KVac/1min.(input/output)（RS-485(Isolating)） 1600 Vdc (input/output) （RS-485(Isolating)） 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-20
上傳用戶：s363994250
Abstract: Many modern industrial, medical, and commercial applications require temperature measurements in the extended temperature rangewith accuracies of ±0.3°C or better, performed with reasonable cost and often with low power consumption. This article explains how platinumresistance temperature detectors (PRTDs) can perform measurements over wide temperature ranges of -200°C to +850°C, with absolute accuracyand repeatability better than ±0.3°C, when used with modern processors capable of resolving nonlinear mathematical equation quickly and costeffectively. This article is the second installment of a series on PRTDs. For the first installment, please read application note 4875, "High-Accuracy Temperature Measurements Call for Platinum Resistance Temperature Detectors (PRTDs) and Precision Delta-Sigma ADCs."
上傳時間： 2013-11-06
上傳用戶：WMC_geophy
The data plane of the reference design consists of a configurable multi-channel XBERT modulethat generates and checks high-speed serial data transmitted and received by the MGTs. Eachchannel in the XBERT module consists of two MGTs (MGTA and MGTB), which physicallyoccupy one MGT tile in the Virtex-4 FPGA. Each MGT has its own pattern checker, but bothMGTs in a channel share the same pattern generator. Each channel can load a differentpattern. The MGT serial rate depends on the reference clock frequency and the internal PMAdivider settings. The reference design can be scaled anywhere from one channel (two MGTs)to twelve channels (twenty-four MGTs).
上傳時間： 2013-12-25
上傳用戶：jkhjkh1982
Delta-sigma ADCs, with their high accuracy and high noiseimmunity, are ideal for directly measuring many typesof sensors. Nevertheless, input sampling currents canoverwhelm high source impedances or low-bandwidth,micropower signal conditioning circuits. The LTC®2484family of delta sigma converters solves this problem bybalancing the input currents, thussimplifying or eliminatingthe need for signal conditioning circuits.
上傳時間： 2015-01-03
上傳用戶：潛水的三貢
The high defi nition multimedia interface (HDMI) is fastbecoming the de facto standard for passing digitalaudio and video data in home entertainment systems.This standard includes an I2C type bus called a displaydata channel (DDC) that is used to pass extended digitalinterface data (EDID) from the sinkdevice (such as adigital TV) to the source device (such as a digital A/Vreceiver). EDID includes vital information on the digitaldata formats that the sink device can accept. The HDMIspecifi cation requires that devices have less than 50pFof input capacitance on their DDC bus lines, which canbe very diffi cult to meet. The LTC®4300A’s capacitancebuffering feature allows devices to pass the HDMI DDCinput capacitance compliance test with ease.
上傳時間： 2013-11-21
上傳用戶：tian126vip
Accurate measurement of the third order intercept pointfor low distortion IC products such as the LT5514 requirescertain precautions to be observed in the test setup andtesting procedure. The LT5514 linearity performance ishigh enough to push the test equipment and test set-up totheir limits. A method for accurate measurement of thirdorder intermodulation products, IM3, with standard testequipment is outlined below.It is also important to correctly interpret the LT5514specification with respect to ROUT, and the impact ofdemo-board transmission-line termination loss whenevaluating the linearity performance, as explained in theLT5514 Datasheet and in Note 1 of this document.
上傳時間： 2013-11-14
上傳用戶：l254587896
基于通用集成運算放大器，利用MASON公式設計了一個多功能二階通用濾波器，能同時或分別實現低通、高通和帶通濾波，也能設計成一個正交振蕩器。電路的極點頻率和品質因數能夠獨立、精確地調節。電路使用4個集成運放、2個電容和11個電阻，所有集成運放的反相端虛地。利用計算機仿真電路的通用濾波功能、極點頻率和品質因數的獨立控制和正交正弦振蕩，從而證明該濾波器正確有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
上傳時間： 2013-10-09
上傳用戶：13788529953
在Multisim 10軟件環境下，設計一種由運算放大器構成的精確可控矩形波信號發生器，結合系統電路原理圖重點闡述了各參數指標的實現與測試方法。通過改變RC電路的電容充、放電路徑和時間常數實現了占空比和頻率的調節，通過多路開關投入不同數值的電容實現了頻段的調節，通過電壓取樣和同相放大電路實現了輸出電壓幅值的調節并提高了電路的帶負載能力，可作為頻率和幅值可調的方波信號發生器。Multisim 10仿真分析及應用電路測試結果表明，電路性能指標達到了設計要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上傳時間： 2014-01-21
上傳用戶：shen007yue
This application note discusses a variety of approaches for interfacing analog signals to 5V powered systems. Synthesizing a "rail-to-rail" op amp and scaling techniques for A/D converters are covered. A voltage-to-frequency converter, applicable where high resolution is required, is also presented.
上傳時間： 2013-10-12
上傳用戶：181992417
超聲波傳感器適用于對大幅的平面進行靜止測距。普通的超聲波傳感器測距范圍大概是 2cm~450cm，分辨率3mm（淘寶賣家說的，筆者測試環境沒那么好，個人實測比較穩定的 距離10cm~2m 左右，超過此距離就經常有偶然不準確的情況發生了，當然不排除筆者技術 問題。） 測試對象是淘寶上面最便宜的SRF-04 超聲波傳感器，有四個腳：5v 電源腳（Vcc），觸發控制端（Trig），接收端（Echo），地端（GND） 附:SRF 系列超聲波傳感器參數比較 模塊工作原理： 采用IO 觸發測距，給至少10us 的高電平信號； 模塊自動發送8個40KHz 的方波，自動檢測是否有信號返回； 有信號返回，通過IO 輸出一高電平，高電平持續的時間就是超聲波從發射到返回的時間．測試距離=(高電平時間*聲速(340m/s))/2; 電路連接方法 Arduino 程序例子： constintTrigPin = 2; constintEchoPin = 3; floatcm; voidsetup() { Serial.begin(9600); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT); } voidloop() { digitalWrite(TrigPin, LOW); //低高低電平發一個短時間脈沖去TrigPin delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite(TrigPin, LOW); cm = pulseIn(EchoPin, HIGH) / 58.0; //將回波時間換算成cm cm = (int(cm * 100.0)) / 100.0; //保留兩位小數 Serial.print(cm); Serial.print("cm"); Serial.println(); delay(1000); }
上傳時間： 2013-11-01
上傳用戶：xiaoyuer
