-
internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
標簽：
Exter
easy
work
with
上傳時間：
2013-10-27
上傳用戶：zhangyigenius
-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
標簽：
Signal
Input
Fall
Rise
上傳時間：
2013-10-23
上傳用戶：copu
-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
標簽：
C16x
微控制器
輸入信號
時序圖
上傳時間：
2014-04-02
上傳用戶：han_zh
-
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
標簽：
3.3
看門狗
芯片
上傳時間：
2013-10-22
上傳用戶：taiyang250072
-
In the past decade, the size and complexity of manyFPGA designs exceeds the time and resourcesavailable to most design teams, making the use andreuse of Intellectual Property (IP) imperative.However, integrating numerous IP blocks acquiredfrom both internal and external sources can be adaunting challenge that often extends, rather thanshortens, design time. As today's designs integrateincreasing amounts of functionality, it is vital thatdesigners have access to proven, up-to-date IP fromreliable sources.
標簽：
AXI4
379
wp
即插即用
上傳時間：
2013-11-15
上傳用戶：lyy1234
-
1 Communication Protocol (Computer as master)
The communication protocol describes here allows your computer to access 4096 internal registers (W0000-W4095) and 1024 internal relays (B0000-B1023) in the Workstation..
1.1 Request Message Format
Request message is a command message to be sent from the computer to the Workstation. The data structure of request message is shown below. Note that numbers are always in hexadecimal form and converted into ASCII characters. For example, Workstation unit number 14 will appear in the message as character 0(30h) followed by character E(45h); a BCC of 5Ah will appear in the message as character 5(35h) followed by character A(41h).
標簽：
HITECH
電腦
通信協議
上傳時間：
2013-10-28
上傳用戶：cxl274287265
-
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
標簽：
Cortex-M
1850
LPC
內核微控制器
上傳時間：
2014-12-31
上傳用戶：zhuoying119
-
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
標簽：
4300
LPC
ARM
雙核微控制器
上傳時間：
2013-10-28
上傳用戶：15501536189
-
使用Nios II軟件構建工具
This chapter describes the Nios® II Software Build Tools (SBT), a set of utilities and
scripts that creates and builds embedded C/C++ application projects, user library
projects, and board support packages (BSPs). The Nios II SBT supports a repeatable,
scriptable, and archivable process for creating your software product.
You can invoke the Nios II SBT through either of the following user interfaces:
■ The Eclipse™ GUI
■ The Nios II Command Shell
The purpose of this chapter is to make you familiar with the internal functionality of
the Nios II SBT, independent of the user interface employed.
標簽：
Nios
軟件
上傳時間：
2013-10-12
上傳用戶：china97wan
-
In the past decade, the size and complexity of manyFPGA designs exceeds the time and resourcesavailable to most design teams, making the use andreuse of Intellectual Property (IP) imperative.However, integrating numerous IP blocks acquiredfrom both internal and external sources can be adaunting challenge that often extends, rather thanshortens, design time. As today's designs integrateincreasing amounts of functionality, it is vital thatdesigners have access to proven, up-to-date IP fromreliable sources.
標簽：
AXI4
379
wp
即插即用
上傳時間：
2013-11-11
上傳用戶：csgcd001
