介紹一種基于單片機的多路溫度采集及監控系統，能夠測量6路溫度信號，具有計算機聯網功能，各測量點可以單獨監控和設置，可根據用戶的需求自動控制。測量溫度范圍為-10 ℃～200 ℃，控制方式采用模擬量調壓模式。該系統具有控制精度高、沖擊小等特點。
Abstract:
A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can measure 6 channel signal of the temperature,and it has a function of network connection.The temperature measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。
Abstract:
In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
以S3C825A為例介紹三星公司SAM8系列單片機的內部結構及其軟件開發環境，詳細描述采用混合編程法來對SAM8系列單片機進行軟件設計的一般方法，最后給出用混合編程法對S3C825A進行軟件設計的具體應用實例。
Abstract:
With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
隨著單片機功能集成化的發展，其應用領域也逐漸地由傳統的控制，擴展為控制處理、數據處理以及數字信號處理（DSP，Digital Signal Processing）等領域。凌陽的16位單片機就是為適應這種發展而設計的。它的CPU內核采用凌陽最新推出的µ’nSP™（Microcontroller and Signal Processor）16位微處理器芯片（以下簡稱µ’nSP™）。圍繞µ’nSP™所形成的16位µ’nSP™系列單片機（以下簡稱µ’nSP™家族）采用的是模塊式集成結構，它以µ’nSP™內核為中心集成不同規模的ROM、RAM和功能豐富的各種外設接口部件。
dsPIC30F產品手冊
High Performance Digital Signal Controllers
This section of the manual contains the following topics:1.1 Introduction 1.2 Manual Objective 1.3 Device Structure1.4 Development Support 1.5 Style and Symbol Conventions 1.6 Related Documents 1.7 Revision History
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
This application note describes how to decode standard DTMF tones using the minimum number of external discrete components and a PIC. The two examples use a PIC which has an 8 bit timer and either a comparator or an ADC, although it can be modified for use on a PIC which has only digital I/O. The Appendices have example code for the 16C662 (with comparator) and 16F877 (using the ADC).
As the majority of the Digital Signal Processing is done in software, little is required in the way of external signal conditioning. Software techniques are used to model the individual elements of a DTMF Decoder IC.
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
The P82B96 offers many different ways in which it can be used as abus interface. In its simplest application it can be used as aninterface between bus systems operating from different supplyvoltages. Opto isolation between two bus systems is possible, andalso the availability of the Tx and Rx signals permits interfacing ofthe P82B96 with other bus systems which separate the forwardoutput path, from the backward input signal path.
