This an adaptive receiver for a direct-sequence spread spectrum (DS-SS) system over an AWGN channel. The adaptive receiver block is modified from the LMS adaptive filter block in DSP Blockset. For DS-SS signal reception, the adaptive filter needs to have multi-rate operation. The input sample rate is equal to chip rate and the output is at symbol rate. Two rates are related by PG, processing gain
This project is created using the Keil ARM CA Compiler.
The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1
This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series.
You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
to show the waveform of audio file and play it on computer
Purpose: Familiar with WAV file format and UI design
It should have the following functions:
Provide a Graphic User Interface for user to browse the file system and select one WAV file
Show the waveform of input audio signal
Play the selected WAV file
Print the parameters of WAV file such as sampling rate, bit-depth, etc
物流分析工具包。Facility location: Continuous minisum facility location, alternate location-allocation (ALA) procedure, discrete uncapacitated facility location
Vehicle routing: VRP, VRP with time windows, traveling salesman problem (TSP)
Networks: Shortest path, min cost network flow, minimum spanning tree problems
Geocoding: U.S. city or ZIP code to longitude and latitude, longitude and latitude to nearest city, Mercator projection plotting
Layout: Steepest descent pairwise interchange (SDPI) heuristic for QAP
Material handling: Equipment selection
General purpose: Linear programming using the revised simplex method, mixed-integer linear programming (MILP) branch and bound procedure
Data: U.S. cities with populations of at least 10,000, U.S. highway network (Oak Ridge National Highway Network), U.S. 3- and 5-digit ZIP codes
This applet illustrates the prediction capabilities of the multi-layer perceptrons. It allows to define an input signal on which prediction will be performed. The user can choose the number of input units, hidden units and output units, as well as the delay between the input series and the predicted output series. Then it is possible to observe interesting prediction properties.
This application report introduces and describes an MP3 /AAC audio player for use with the TMS320C54x(TM) digital signal processor (DSP) devices. This audio player is based on Reference Framework Level 3 (RF3). Reference Framework for eXpressDSP(TM) Software is a start-ware for developing applications that use DSP/BIOS(TM) and the TMS320(TM) DSP AlgorithmStandard.
Simulator for a GSM traffic channel transmission and reception
This Simulink model simulates the entire transmission and reception of voice data of a traffic channel for GSM (TCH/FS)over a multipath fading channel, and it calculates the BER of the received signal
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
