For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上傳時間： 2013-10-19
上傳用戶：royzhangsz
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
上傳時間： 2013-10-12
上傳用戶：司令部正軍級
在理論分析循環碼編碼和譯碼基本原理的基礎上，提出了基于單片機系統的(24，16)循環碼軟件實現編碼、譯碼的方案。仿真結果表明(24，16)循環碼能有效地克服來自通訊信道的干擾，保證數據通信的可靠及系統的穩定，使誤碼率大幅度降低。本論文對(24，16)循環碼的研究結果表明，可以有效地降低錯誤概率和提高系統的吞吐量，實現糾錯僅需要在接收端增加有限的存儲空間和計算復雜度，具有一定的實用價值。 Abstract: Based on analyzing the theory of encoding and decoding of cyclic code， this paper showed the schemes of encoding and decoding of(24，16)cyclic code by the software and based on microcontroller. Simulation results show that using (24，16) cyclic codes can effectively overcome the interference from communication channel， ensure the reliability and stability of data communication systems， and reduce the bit error rate greatly. The results of this paper show that by using the (24，16) cyclic code， the error rate can be reduced and the system throughput can be improved. Meanwhile， the system only needs to enlarge limited storage space and computation the complexity at the receiving end to realize error correction. Thus the (24，16) cyclic code has a practical value.
上傳時間： 2013-11-09
上傳用戶：gaoliangncepu
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上傳時間： 2013-10-15
上傳用戶：urgdil
基于CC1110單片機公交報站系統主要由CC1110單片機最小系統和WT588D語音模塊組成，提出了如何實現語音報站，通過無線通信SimpliciTI網絡協議實現公交站臺的自動播報和OLCD液晶顯示公交運行的各類信息。結果表明，該公交報站系統報站準確率99%，價格比同類產品下降了300%以上，系統組成結構簡單，提高了系統的抗干擾性和穩定性，也便于攜帶。 Abstract: The bus stop announcement system based on CC1110 MCU is composed of CC1110 MCU minimum system and WT588D voice module. How to achieve the voice announcing is put forward.The bus-stop will announce automatically and display on the OLCD by means of wireless communication SimpliciTI network protocol. As a result， the bus station stop announcement systems reported 99% accuracy rate， price of similar products declined by 300% or more， system of simple structure， improve the anti-jamming and stability of the power system， it is also portable.
上傳時間： 2013-10-21
上傳用戶：baby25825
為解決輸油管道溫度壓力參數實時監測的問題，設計了以C8051F930單片機作為控制核心的超低功耗輸油管道溫度壓力遠程監測系統。現場儀表使用高精度電橋采集數據，通過433 MHz短距離無線通信網絡與遠程終端RTU進行通信，RTU通過GPRS網絡與PC上位機進行遠程數據傳輸，在上位機中實現數據存儲和圖形化界面顯示，從而實現輸油管道溫度壓力參數的實時監測和異常報警。經實驗證明，該系統的12位數據采集精度滿足設計要求，漏碼率小于1%，正常工作時間超過5個月，能實時有效地監測輸油管道的溫度壓力參數，節省大量人工成本，有效預防管道參數異常造成的經濟損失和環境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上傳時間： 2013-11-07
上傳用戶：cuibaigao
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上傳時間： 2013-11-15
上傳用戶：zouxinwang
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
標簽： Pulsoximeter Single-Chip Des
上傳時間： 2013-10-27
上傳用戶：黑漆漆
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
標簽： MULTICHANNEL 5.5 TO RS
上傳時間： 2013-10-19
上傳用戶：ddddddd
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上傳時間： 2013-10-23
上傳用戶：copu
