The P82B715 I2C Buffer was designed toextend the range of the local I2C bus out to50 Meters. This application note describesthe results of testing the buffer on severaldifferent types of cables to determine themaximum operating distances possible. Theresults are summarized in a table for easyreference.
XAPP520將符合2.5V和3.3V I/O標準的7系列FPGA高性能I/O Bank進行連接
The I/Os in Xilinx® 7 series FPGAs are classified as either high range (HR) or high performance (HP) banks. HR I/O banks can be operated from 1.2V to 3.3V, whereas HP I/O banks are optimized for operation between 1.2V and 1.8V. In circumstances that require an HP 1.8V I/O bank to interface with 2.5V or 3.3V logic, a range of options can be deployed. This application note describes methodologies for interfacing 7 series HP I/O banks with 2.5V and 3.3V systems
各種功能的計數器實例（VHDL源代碼）:ENTITY counters IS
PORT
(
d : IN INTEGER RANGE 0 TO 255;
clk : IN BIT;
clear : IN BIT;
ld : IN BIT;
enable : IN BIT;
up_down : IN BIT;
qa : OUT INTEGER RANGE 0 TO 255;
qb : OUT INTEGER RANGE 0 TO 255;
qc : OUT INTEGER RANGE 0 TO 255;
qd : OUT INTEGER RANGE 0 TO 255;
qe : OUT INTEGER RANGE 0 TO 255;
qf : OUT INTEGER RANGE 0 TO 255;
qg : OUT INTEGER RANGE 0 TO 255;
qh : OUT INTEGER RANGE 0 TO 255;
qi : OUT INTEGER RANGE 0 TO 255;
The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
We offer a broad line of high performance low dropout (LDO) linear regulators with fasttransient response, excellent line and load regulation, and very wide input voltage rangefrom 0.9V to 100V. Output currents range from 20mA to 10A, with positive, negative andmultiple output versions available. Many devices offer output voltage operation <0.8V andsome feature operation as low as 0V, even with a single supply. Most are stable with ceramicoutput capacitors. LDO regulators can be applied in virtually any application.
Abstract: The process of designing a radio system can be complex and often involves many project tradeoffs. Witha little insight, balancing these various characteristics can make the job of designing a radio system easier. Thistutorial explores these tradeoffs and provides details to consider for various radio applications. With a focus on theindustrial, scientific, medical (ISM) bands, the subjects of frequency selection, one-way versus two-way systems,modulation techniques, cost, antenna options, power-supply influences, effects on range, and protocol selectionare explored.
Agilent AN 154 S-Parameter Design Application Note S參數的設計與應用
The need for new high-frequency, solid-state circuitdesign techniques has been recognized both by microwaveengineers and circuit designers. These engineersare being asked to design solid state circuitsthat will operate at higher and higher frequencies.The development of microwave transistors andAgilent Technologies’ network analysis instrumentationsystems that permit complete network characterizationin the microwave frequency rangehave greatly assisted these engineers in their work.The Agilent Microwave Division’s lab staff hasdeveloped a high frequency circuit design seminarto assist their counterparts in R&D labs throughoutthe world. This seminar has been presentedin a number of locations in the United States andEurope.From the experience gained in presenting this originalseminar, we have developed a four-part videotape, S-Parameter Design Seminar. While the technologyof high frequency circuit design is everchanging, the concepts upon which this technologyhas been built are relatively invariant.The content of the S-Parameter Design Seminar isas follows:
