交流電壓，電流轉換器 特點： 精確度0.25%滿刻度(RMS) 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 2:主要規格 精確度:0.25%F.S.(RMS) (23 ±5℃) 輸入負載: <0.2VA(voltage) <0.2VA(current) 最大過載能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2x rated continuous 輸出反應時間: <250ms (0~90%) 輸出負載能力: <10mA for voltage mode <10V for current mode 輸出漣波: <0.1% F.S. 歸零調整范圍: 0~±5% F.S. 最大值調整范圍: 0~±10% F.S. 溫度系數: 100ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 行動測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波測試: 2.5KV-0.25ms/1MHz 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
Abstract: What can be simpler than designing with CMOS and BiCMOS? These technologies are very easy to use butthey still require careful design. This tutorial discusses the odd case of circuits that seem to work but exhibit somepeculiar behaviors—including burning the designer's fingers!
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
With more and more multi-frequency clocks being used in today's chips, especially in the communications field, it is often necessary to switch the source of a clock line while the chip is running.
Abstract: IC switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-acquisition systems.
Sensors for pressure, load, temperature, acceleration andmany other physical quantities often take the form of aWheatstone bridge. These sensors can be extremely linearand stable over time and temperature. However, mostthings in nature are only linear if you don’t bend them toomuch. In the case of a load cell, Hooke’s law states that thestrain in a material is proportional to the applied stress—as long as the stress is nowhere near the material’s yieldpoint (the “point of no return” where the material ispermanently deformed).
One of the most critical components in a step-up design like Figure 1 is the transformer. Transformers have parasitic components that can cause them to deviate from their ideal characteristics, and the parasitic capacitance associated with the secondary can cause large resonating current spikes on the leading edge of the switch current waveform.
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
Calculation of the Differential Impedance of Tracks on FR4 substrates
There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
