Keil uVision2是目前使用廣泛的單片機開發軟件，它集成了源程序編輯和程序調試于一體，支持匯編、C、PL/M語言。 這里我們僅僅介紹 Keil uVision2 的簡單使用，更詳細的使用方法見本光盤\單片機軟件\Keil c51\Keil書籍與資料目錄中的內容。 keil C51 v6.12 的安裝： 先運行光盤中 單片機軟件\setup\setup.exe 安裝程序，選擇安裝“Eval Version”版進行安裝。一直點擊“Yes”或“Next”，直到“Finish”完成。 之后運行同目錄中的 Keil uv2 漢化安裝.exe 安裝漢化程序。 keil C51 v6.12 的使用： 點擊桌面快捷圖標，可以直接進入主畫面：現在，我們來做個實際程序，請跟著我一步一步學著做，實際體驗一下從編輯源程序到程序調試的全過程。 這里讓我們做一個 讓單片機 P0 口所驅動的 LED 燈隔一個亮隔一個滅 的程序。 在Keil系統中，每做個獨立的程序，都視為工程（或者叫項目）。首先從菜但的“工程”中“新建工程...”，建立我們將要做的工程項目：新建的工程要起個與工程項目意義一致的名字，可以是中文名；我們這里的程序是實驗測試程序，所以起的名字為 Test ，并將 Test 工程“保存”到 C:\Keil 下：接下來，Keil環境要求我們為 Test 工程選擇一個單片機型號；我們選擇 Atmel 公司的 89C51（雖然我們使用的是89S51，但由于89S51與89C51內、外部結構完全一樣，所以這里依然選擇“89C51”）。“確定”后工程項目就算建立了。
上傳時間： 2013-10-12
上傳用戶：zzzzzz
什么是JTAG 到底什么是JTAG呢？ JTAG(Joint Test Action Group)聯合測試行動小組)是一種國際標準測試協議（IEEE 1149.1兼容），主要用于芯片內部測試。現在多數的高級器件都支持JTAG協議，如DSP、FPGA器件等。標準的JTAG接口是4線：TMS、 TCK、TDI、TDO，分別為模式選擇、時鐘、數據輸入和數據輸出線。 JTAG最初是用來對芯片進行測試的，基本原理是在器件內部定義一個TAP（Test Access Port�測試訪問口）通過專用的JTAG測試工具對進行內部節點進行測試。JTAG測試允許多個器件通過JTAG接口串聯在一起，形成一個JTAG鏈，能實現對各個器件分別測試。現在，JTAG接口還常用于實現ISP（In-System rogrammable�在線編程），對FLASH等器件進行編程。 JTAG編程方式是在線編程，傳統生產流程中先對芯片進行預編程現再裝到板上因此而改變，簡化的流程為先固定器件到電路板上，再用JTAG編程，從而大大加快工程進度。JTAG接口可對PSD芯片內部的所有部件進行編程 JTAG的一些說明 通常所說的JTAG大致分兩類，一類用于測試芯片的電氣特性，檢測芯片是否有問題；一類用于Debug；一般支持JTAG的CPU內都包含了這兩個模塊。 一個含有JTAG Debug接口模塊的CPU，只要時鐘正常，就可以通過JTAG接口訪問CPU的內部寄存器和掛在CPU總線上的設備，如FLASH，RAM，SOC（比如4510B，44Box，AT91M系列）內置模塊的寄存器，象UART，Timers，GPIO等等的寄存器。 上面說的只是JTAG接口所具備的能力，要使用這些功能，還需要軟件的配合，具體實現的功能則由具體的軟件決定。 例如下載程序到RAM功能。了解SOC的都知道，要使用外接的RAM，需要參照SOC DataSheet的寄存器說明，設置RAM的基地址，總線寬度，訪問速度等等。有的SOC則還需要Remap，才能正常工作。運行Firmware時，這些設置由Firmware的初始化程序完成。但如果使用JTAG接口，相關的寄存器可能還處在上電值，甚至時錯誤值，RAM不能正常工作，所以下載必然要失敗。要正常使用，先要想辦法設置RAM。在ADW中，可以在Console窗口通過Let 命令設置，在AXD中可以在Console窗口通過Set命令設置。
上傳時間： 2013-10-23
上傳用戶：aeiouetla
針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
上傳時間： 2013-11-17
上傳用戶：lo25643
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上傳時間： 2013-11-06
上傳用戶：liu123
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上傳時間： 2014-01-13
上傳用戶：qoovoop
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
標簽： Transceiver Virtex Wizar GTP
上傳時間： 2013-10-23
上傳用戶：leyesome
UART 4 UART參考設計，Xilinx提供VHDL代碼 uart_vhdl This zip file contains the following folders: \vhdl_source -- Source VHDL files: uart.vhd - top level file txmit.vhd - transmit portion of uart rcvr.vhd - - receive portion of uart \vhdl_testfixture -- VHDL Testbench files. This files only include the testbench behavior, they do not instantiate the DUT. This can easily be done in a top-level VHDL file or a schematic. This folder contains the following files: txmit_tb.vhd -- Test bench for txmit.vhd. rcvr_tf.vhd -- Test bench for rcvr.vhd.
上傳時間： 2013-11-07
上傳用戶：jasson5678
關于GL827L的資料
標簽： Report_SSOP Test 827 102
上傳時間： 2014-01-08
上傳用戶：lz4v4
This application note provides step-by-step instructions on how to recreate a Tri-Mode Ethernet(TEMAC) performance testing system using the ML405 board and MontaVista Linux 4.0. Thisapplication note shows how to set up a simple EDK Base System Builder system on the ML405Evaluation Platform and run performance tests. The network architecture for the test isdescribed. A system is built and downloaded into the FPGA. A MontaVista Linux kernel isconfigured, built, and downloaded into the ML405 Evaluation Platform. The instructions forobtaining and setting up the software used to perform the measurements, netperf, are given.
上傳時間： 2013-11-11
上傳用戶：saharawalker
The #1 Step-by-Step Guide to labviewNow Completely Updated for labview 8! Master labview 8 with the industry's friendliest, most intuitive tutorial: labview for Everyone, Third Edition. Top labview experts Jeffrey Travis and Jim Kring teach labview the easy way: through carefully explained, step-by-step examples that give you reusable code for your own projects! This brand-new Third Edition has been fully revamped and expanded to reflect new features and techniques introduced in labview 8. You'll find two new chapters, plus dozens of new topics, including Project Explorer, AutoTool, XML, event-driven programming, error handling, regular expressions, polymorphic VIs, timed structures, advanced reporting, and much more. Certified labview Developer (CLD) candidates will find callouts linking to key objectives on NI's newest exam, making this book a more valuable study tool than ever. Not just what to d why to do it! Use labview to build your own virtual workbench Master labview's foundations: wiring, creating, editing, and debugging VIs; using controls and indicators; working with data structures; and much more Learn the "art" and best practices of effective labview development NEW: Streamline development with labview Express VIs NEW: Acquire data with NI-DAQmx and the labview DAQmx VIs NEW: Discover design patterns for error handling, control structures, state machines, queued messaging, and more NEW: Create sophisticated user interfaces with tree and tab controls, drag and drop, subpanels, and more Whatever your application, whatever your role, whether you've used labview or not, labview for Everyone, Third Edition is the fastest, easiest way to get the results you're after!
上傳時間： 2013-10-14
上傳用戶：shawvi
