This application note provides a detailed description of the Spartan™-3 configurationarchitecture. It explains the composition of the bitstream file and how this bitstream isinterpreted by the configuration logic to program the part. Additionally, a methodology ispresented that will guide the user through the readback process. This information can be usedfor partial reconfiguration or partial readback.
上傳時間： 2013-11-05
上傳用戶：透明的心情
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the blockmemory in terms of bits per second will remain the same.
上傳時間： 2013-11-08
上傳用戶：lou45566
Express Mode uses an 8-bit wide bus path for fast configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
標簽： Spartan-XL Express XAPP FPGA
上傳時間： 2014-12-28
上傳用戶：hewenzhi
The introduction of Spartan-3™ devices has createdmultiple changes in the evolution of embedded controldesigns and pushed processing capabilities to the “almostfreestage.” With these new FPGAs falling under $20, involume, with over 1 million system gates, and under $5for 100K gate-level units, any design with programmablelogic has a readily available 8- or 16-bit processor costingless than 75 cents and 32-bit processor for less than $1.50.
上傳時間： 2013-12-10
上傳用戶：zgu489
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上傳時間： 2013-10-15
上傳用戶：euroford
The Virtex™-4 user access register (USR_ACCESS_VIRTEX4) is a 32-bit register thatprovides direct access to bitstream data by the FPGA fabric. It is useful for loadingPowerPC™ 405 (PPC405) processor caches and/or other data into the FPGA after the FPGAhas been configured, thus achieving partial reconfiguration. The USR_ACCESS_VIRTEX4register is programmed through the bitstream with a command that writes a series of 32-bitwords.
標簽： USR_ACCESS PowerPC XAPP 719
上傳時間： 2013-11-13
上傳用戶：我累個乖乖
The PPC405 Virtex-4 is a wrapper around the Virtex-4PowerPC™ 405 Processor Block primitive. For detailsregarding the PowerPC 405, see the PowerPC 405 ProcessorBlock Reference Guide.
上傳時間： 2014-12-05
上傳用戶：flg0001
Xilinx Next Generation 28 nm FPGA Technology Overview Xilinx has chosen 28 nm high-κ metal gate (HKMG) highperformance,low-power process technology and combined it with a new unified ASMBL™ architecture to create a new generation of FPGAs that offer lower power and higher performance. These devices enable unprecedented levels of integration and bandwidth and provide system architects and designers a fully programmable alternative to ASSPs and ASICs.
上傳時間： 2014-12-28
上傳用戶：zhang97080564
WP369可擴展式處理平臺-各種嵌入式系統(tǒng)的理想解決方案 ：Delivering unrivaled levels of system performance,flexibility, scalability, and integration to developers,Xilinx's architecture for a new Extensible Processing Platform is optimized for system power, cost, and size. Based on ARM's dual-core Cortex™-A9 MPCore processors and Xilinx’s 28 nm programmable logic,the Extensible Processing Platform takes a processor-centric approach by defining a comprehensive processor system implemented with standard design methods. This approach provides Software Developers a familiar programming environment within an optimized, full featured,powerful, yet low-cost, low-power processing platform.
上傳時間： 2013-10-22
上傳用戶：685
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-14
上傳用戶：fdmpy
蟲蟲下載站版權(quán)所有 京ICP備2021023401號-1
