This application note provides a detailed description of the Spartan™-3 configurationarchitecture. It explains the composition of the bitstream file and how this bitstream isinterpreted by the configuration logic to program the part. Additionally, a methodology ispresented that will guide the user through the readback process. This information can be usedfor partial reconfiguration or partial readback.
上傳時間： 2013-11-16
上傳用戶：qingdou
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the blockmemory in terms of bits per second will remain the same.
上傳時間： 2014-01-24
上傳用戶：15527161163
Express Mode uses an 8-bit wide bus path for fast configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
標簽： Spartan-XL Express XAPP FPGA
上傳時間： 2015-01-02
上傳用戶：nanxia
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software operations and provides an overview of theadditional operations supported by XC9500/XL/XV CPLDs for in-system programming.
上傳時間： 2013-11-01
上傳用戶：南國時代
Virtex™-5 器件包括基于第二代高級硅片組合模塊 (ASMBL™) 列架構的多平臺 FPGA 系列。集成了為獲得最佳性能、更高集成度和更低功耗設計的若干新型架構元件，Virtex-5 器件達到了比以往更高的系統性能水平。
上傳時間： 2013-10-19
上傳用戶：giraffe
This application note provides a functional description of VHDL source code for a N x N DigitalCrosspoint Switch. The code is designed with eight inputs and eight outputs in order to targetthe 128-macrocell CoolRunner™-II CPLD device but can be easily expanded to target higherdensity devices. To obtain the VHDL source code described in this document, go to sectionVHDL Code, page 5 for instructions.
標簽： CoolRunner-II XAPP CPLD 380
上傳時間： 2013-10-26
上傳用戶：kiklkook
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上傳時間： 2014-11-26
上傳用戶：erkuizhang
The introduction of Spartan-3™ devices has createdmultiple changes in the evolution of embedded controldesigns and pushed processing capabilities to the “almostfreestage.” With these new FPGAs falling under $20, involume, with over 1 million system gates, and under $5for 100K gate-level units, any design with programmablelogic has a readily available 8- or 16-bit processor costingless than 75 cents and 32-bit processor for less than $1.50.
上傳時間： 2013-10-21
上傳用戶：ligi201200
The Virtex™-4 user access register (USR_ACCESS_VIRTEX4) is a 32-bit register thatprovides direct access to bitstream data by the FPGA fabric. It is useful for loadingPowerPC™ 405 (PPC405) processor caches and/or other data into the FPGA after the FPGAhas been configured, thus achieving partial reconfiguration. The USR_ACCESS_VIRTEX4register is programmed through the bitstream with a command that writes a series of 32-bitwords.
標簽： USR_ACCESS PowerPC XAPP 719
上傳時間： 2013-12-23
上傳用戶：yuanwenjiao
The PPC405 Virtex-4 is a wrapper around the Virtex-4PowerPC™ 405 Processor Block primitive. For detailsregarding the PowerPC 405, see the PowerPC 405 ProcessorBlock Reference Guide.
上傳時間： 2015-01-02
上傳用戶：JIUSHICHEN
