A programmable digital signal processor (PDSP) is a special-purpose Microprocessor
with specialized architecture and instruction set for implementing DSP
algorithms. Typical architectural features include multiple memory partitions (onchip,
off-chip, data memory, program memory, etc.), multiple (generally pipelined)
arithmetic and logic units (ALUs), nonuniform register sets, and extensive
hardware numeric support [1,2]. Single-chip PDSPs have become increasingly
popular for real-time DSP applications [3,4].
This manual describes SAMSUNG s S3C2410X 16/32-bit RISC Microprocessor. This product is designed to
provide hand-held devices and general applications with cost-effective, low-power, and high-performance microcontroller
solution in small die size. To reduce total system cost, the S3C2410X includes the following
components separate 16KB Instruction and 16KB Data Cache, MMU to handle virtual memory management,
LCD Controller (STN & TFT), NAND Flash Boot Loader, System Manager (chip select logic and SDRAM
Controller), 3-ch UART, 4-ch DMA, 4-ch Timers with PWM, I/O Ports, RTC, 8-ch 10-bit ADC and Touch Screen
Interface, IIC-BUS Interface, IIS-BUS Interface, USB Host, USB Device, SD Host & Multi-Media Card Interface,
2-ch SPI and PLL for clock generation.
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC converter. The digital adjustmentmethods are with a digital-to-analog converter (DAC), a trim pot (digital potentiometer), and PWM output of a Microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
Abstract: Using a DAC and a Microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when aMicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
This application note features 8-, 10-, and 12-bit dataacquisition components in various circuit configurations.The circuits include battery monitoring, temperature sensing,isolated serial interfaces, and Microprocessor andmicrocontroller serial and parallel interfaces. Also includedare voltage reference circuits (Application Note 42contains more voltage reference circuits).
The LTC®3562 quad output step-down regulator is designedfor multicore handheld Microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard Microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
The LTC®4099 high effi ciency USB power manager andLi-Ion/Polymer battery charger seamlessly managespower distribution from multiple sources in portableapplications. It is differentiated from other USB powermanagers by its bidirectional I2C port that allows the hostMicroprocessor to control and monitor all aspects of theUSB power management and battery charging processes.In addition, a programmable interrupt generation functionalerts the host Microprocessor to changes in device statusand provides unprecedented control of power managementfunctions. This high degree of confi gurability allowspost-layout changes in operation, even changes in thefi eld, and it allows a single qualifi ed device to be usedin a variety of products, thus reducing design time andeasing inventory management.
Providing power for the Pentium® Microprocessor family isnot a trivial task by any means. In an effort to simplify thistask we have developed a new switching regulator controlcircuit and a new linear regulator to address the needs ofthese processors. Considerable time has been spent developingan optimized decoupling network. Here are severalcircuits using the new LTC®1266 synchronous buck regulatorcontrol chip and the LT®1584 linear regulator toprovide power for Pentium processors and Pentium VREprocessors. The Pentium processor has a supply requirementof 3.3V ±5%. The Pentium VRE processor requires3.500V ±100mV.
