The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
標簽： synchronous Emulating serial
上傳時間： 2014-01-31
上傳用戶：z1191176801
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
標簽： Bridge Memory Contr MPC
上傳時間： 2013-10-08
上傳用戶：18711024007
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上傳時間： 2014-01-06
上傳用戶：氣溫達上千萬的
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
標簽： software driver XA-S I2C
上傳時間： 2013-11-02
上傳用戶：zw380105939
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上傳時間： 2013-11-10
上傳用戶：liaofamous
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
標簽： iButtons Reading Writing and
上傳時間： 2013-10-29
上傳用戶：long14578
The 87LPC76X Microcontroller combines in a small package thebenefits of a high-performance microcontroller with on-boardhardware supporting the Inter-Integrated Circuit (I2C) bus interface.The 87LPC76X can be programmed both as an I2C bus master, aslave, or both. An overview of the I2C bus and description of the bussupport hardware in the 87LPC76X microcontrollers appears inapplication note AN464, Using the 87LPC76X Microcontroller as anI2C Bus Master. That application note includes a programmingexample, demonstrating a bus-master code. Here we show anexample of programming the microcontroller as an I2C slave.The code listing demonstrates communications routines for the87LPC76X as a slave on the I2C bus. It compliments the program inAN464 which demonstrates the 87LPC76X as an I2C bus master.One may demonstrate two 87LPC76X devices communicating witheach other on the I2C bus, using the AN464 code in one, and theprogram presented here in the other. The examples presented hereand in AN464 allow the 87LPC76X to be either a master or a slave,but not both. Switching between master and slave roles in amultimaster environment is described in application note AN435.The software for a slave on the bus is relatively simple, as theprocessor plays a relatively passive role. It does not initiate bustransfers on its own, but responds to a master initiating thecommunications. This is true whether the slave receives or transmitsdata—transmission takes place only as a response to a busmaster’s request. The slave does not have to worry about arbitrationor about devices which do not acknowledge their address. As theslave is not supposed to take control of the bus, we do not demandit to resolve bus exceptions or “hangups”. If the bus becomesinactive the processor simply withdraws, not interfering with themaster (or masters) on the bus which should (hopefully) try toresolve the situation.
標簽： routines slave I2C 87L
上傳時間： 2013-11-19
上傳用戶：shirleyYim
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
標簽： microcontro Using 76X LPC
上傳時間： 2013-12-30
上傳用戶：Artemis
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
標簽： Infra-red Remote Cont 05K
上傳時間： 2014-01-24
上傳用戶：zl5712176
蟲蟲下載站版權所有 京ICP備2021023401號-1
