％ because we do not truncate and shift the convolved input ％ sequence, the delay of the desired output sequence wrt ％ the convolved input sequence need only be the delay ％ introduced by the ideal weight vector centred at n=5
標簽： the convolved truncate sequence
上傳時間： 2015-12-27
上傳用戶：www240697738
This example streams input from a ADC source to a DAC. An analog signal is acquired block-by-block into SDRAM from the ADC (an AD9244 in this example). The frames are then output with a one-frame delay to the DAC (an AD9744 in this example). In this example, no processing is done on the frames. They are passed unaltered.
標簽： block-by-block acquired example streams
上傳時間： 2015-12-29
上傳用戶：bjgaofei
① 使用自動機技術實現一個詞法分析程序； ② 使用算符優先分析方法實現其語法分析程序； 需要先在運行目錄下建立一個input.txt文件，將需要分析的文法放在該文件中，分析結果，會輸出在output.txt文件中。
上傳時間： 2013-12-09
上傳用戶：stampede
可編程并行接口８２５５Ａ完成的交通燈實驗 用８２５５Ａ的Ｂ端口和Ｃ端口控制１２個ＬＥＤ的亮和滅（輸出為０則亮，輸出為１則滅），模擬十字路口的交通燈。 -programmable parallel interface 8255A completed, the traffic lights experimental 8255A port B and C - I control 12 LED bright and methomyl (output of 0-liang, the output of an anti), the simulation of traffic lights at a crossroads.
上傳時間： 2016-08-13
上傳用戶：來茴
This file implements a pid controller used to simulator cruise control in a car The input is a throtle value between 0 - 100 ( read on P1 ) The output is the car s speed ( P2 - P0 )
標簽： controller implements simulator control
上傳時間： 2014-01-01
上傳用戶：13160677563
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2013-12-13
上傳用戶：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2014-01-20
上傳用戶：三人用菜
a Java program that reads in the following values from the standard input device (i.e. Keyboard) and writes its result on the standard output device (i.e. Console/Monitor): Inputs: A: the loan amount in dollars and cents (e.g. 150000.00). r: the net annual interest rate, expressed as an integer (e.g. 10 which means 10％) Y: the number of whole remaining years (for repayment) M: the number of remaining months Output: The program should calculate and output the amount of monthly repayments in dollars and cents as single value (e.g. $840.55)
標簽： i.e. following the Keyboard
上傳時間： 2013-12-15
上傳用戶：米卡
Produce Java classes to calculate and display the Poisson probability when input the value of the average (A) arrival rate of customers at some business in the range of 1 to 10. The error message will output when A is out of the range。
標簽： the probability calculate Produce
上傳時間： 2014-01-10
上傳用戶：moerwang
Flex chip implementation File: UP2FLEX JTAG jumper settings: down, down, up, up Input: Reset - FLEX_PB1 Input n - FLEX_SW switches 1 to 8 Output: Countdown - two 7-segment LEDs. Done light - decimal point on Digit1. Operation: Setup the binary input n number. Press the Reset switch. See the countdown from n down to 0 on the 7-segment LEDs. Done light lit when program terminates.
標簽： down implementation settings UP2FLEX
上傳時間： 2014-01-21
上傳用戶：sclyutian
<del id="owcas"></del>