Example - 3-D Stem Plot of an FFTFor example, fast Fourier transforms are calculated at points around the unit circle on the complex plane. So, it is interesting to visualize the plot around the unit circle. calculating the unit circle.
標簽： calculated transforms Example Fourier
上傳時間： 2013-12-17
上傳用戶：wpwpwlxwlx
％ DYNMODES calculates ocean dynamic vertical modes ％ taking a column vector of Brunt-Vaisala values (Nsq) at ％ different pressures (p) and calculating some number of ％ dynamic modes (nmodes). ％ Note: The input pressures need not be uniformly spaced, ％ and the deepest pressure is assumed to be the bottom.
標簽： Brunt-Vaisala calculates DYNMODES vertical
上傳時間： 2013-12-06
上傳用戶：busterman
1D FDTD simulation between free space and dielectric medium with absorbing boundary conditions,calculating the fourier transform of electric field
標簽： simulation dielectric conditions absorbing
上傳時間： 2016-09-24
上傳用戶：gundamwzc
This GUI can be used by entering nu at the MATLAB command prompt. The user can either select a function (f(x)) of their choice or a statistical distribution probability distribution function to plot over a user defined range. The function s integral can be evaluated over a user defined range by using: The composite trapezium, simpsons and gauss-legendre rules. This is useful for calculating accurate probabilities that one might see in statistical tables.
標簽： can entering command MATLAB
上傳時間： 2016-11-07
上傳用戶：偷心的海盜
k-step ahead predictions determined by simulation of the ％ one-step ahead neural network predictor. For NNARMAX ％ models the residuals are set to zero when calculating the ％ predictions. The predictions are compared to the observed output. ％
標簽： ahead predictions determined simulation
上傳時間： 2016-12-27
上傳用戶：busterman
This application report discusses the design of non-invasive optical plethysmography also called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). The pulsoximeter consists of a peripheral probe combined with the MCU displaying the oxygen saturation and pulse rate on a LCD glass. The same sensor is used for both heart-rate detection and pulsoximetering in this application. The probe is placed on a peripheral point of the body such as a finger tip, ear lobe or the nose. The probe includes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) and the other in the infrared spectrum (940nm). The percentage of oxygen in the body is worked by measuring the intensity from each frequency of light after it transmits through the body and then calculating the ratio between these two intensities.
標簽： plethysmography non-invasive application discusses
上傳時間： 2014-01-17
上傳用戶：天誠24
Computation of loudness (Zwicker model) according to ISO 532B / DIN 45631 norms. This model is valid for steady sounds. Code based on BASIC program published in the following article: Program for calculating loudness according to DIN 45 631 (ISO 532B)", E.Zwicker and H.Fastl, J.A.S.J (E) 12, 1 (1991).
上傳時間： 2016-11-14
上傳用戶：zztony16
基于FPGA設計的相關論文資料大全 84篇用FPGA實現FFT的研究 劉朝暉 韓月秋 摘 要 目的 針對高速數字信號處理的要求，給出了用現場可編程門陣列(FPGA)實現的 快速傅里葉變換(FFT)方案.方法 算法為按時間抽取的基4算法，采用遞歸結構的塊浮點運 算方案，蝶算過程只擴展兩個符號位以適應雷達信號處理的特點，乘法器由陣列乘法器實 現.結果 采用流水方式保證系統的速度，使取數據、計算旋轉因子、復乘、DFT等操作協 調一致，在計算、通信和存儲間取得平衡，避免了瓶頸的出現.結論 實驗表明，用FPGA 實現高速數字信號處理的算法是一個可行的方案. 關鍵詞 離散傅里葉變換； 快速傅里葉變換； 塊浮點運算； 可編程門陣列 分類號 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the requirement for high speed digital signal processing. Methods The structure of FPGA and requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
標簽： fpga
上傳時間： 2022-03-23
上傳用戶：
