Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
標簽： Converter Defi ADC 轉換器
上傳時間： 2013-11-12
上傳用戶：pans0ul
cv181l-a-20
標簽： Specification_V 181 1.0 L-A
上傳時間： 2013-11-14
上傳用戶：daijun20803
This product integration guide provides application circuit information for theSmartMesh® LTP5903PC wireless embedded network manager. This guide is acompanion to the 020-0039 SmartMesh LTP5903PC Datasheet, whichdescribes overall product behavior, including detailed information about normaloperating conditions, electrical and mechanical specifications, hardware andsoftware interfaces, and connector pinouts.
標簽： Integration Hardware Guide 5903
上傳時間： 2013-11-14
上傳用戶：農藥鋒6
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上傳時間： 2013-11-18
上傳用戶：zhouxuepeng1
Abstract: Stuxnet, a sophisticated virus that damaged Iran's nuclear capability, should be an eye openerfor the world. We can choose to learn something very narrow (how to combat the Stuxnet virus) or wecan choose to focus on the larger goal of thwarting the next type of creative cyber attack. Unfortunately,critical industrial infrastructure is not currently designed with security as a key goal, leaving open multipleavenues for an educated and funded attacker to create massive problems. This tutorial outlines somebasic concepts that engineers and product definers should consider to make sure their new projects stayahead of future threats.
標簽： 智能電網 安全保護
上傳時間： 2013-11-17
上傳用戶：llwap
2012TI杯陜西賽題H題,2012TI杯陜西賽題-A微弱信號檢測裝置.
上傳時間： 2013-12-17
上傳用戶：362279997
2011全國大賽A題開關電源模塊并聯供電系統
標簽： 2011 大賽 開關電源模塊 并聯供電系統
上傳時間： 2013-11-10
上傳用戶：冇尾飛鉈
Avnet Design Service電源實驗室開發出基于MSP430FE427(A) 模塊的電度表解決方案： （1）電壓 (90Vac~264Vac) 與電流 (10Arms) 測量范圍寬 （2）電度表是一種測量用電量的設備 （3）LCD顯示電量 (kWh)、功率 (W)、電壓 (V)、電流 (A)、功率因數(PF) 與溫度 (oC) 測量值 （4）264Vac/63Hz與140mW @90Vac/47Hz條件下，無負載功耗低于300mW （5）測量精度高達2%
上傳時間： 2013-10-13
上傳用戶：cjf0304
PMC和PMC-A系列是小型，高性能，恒定電壓，恒定電流的串聯調節器方式的DC電源。采用串聯調節器方式的設計，可以在低噪聲輸出等級的情況下實現了高穩定的輸出。LED數字儀表在朦朧的環境中也能清晰易讀，電子開關排除了繼電器的顫動，也是這一系列的特征。此外，一部分的PMC-A系列裝備了各種遠程控制功能，通過GPIB，可連接電源控制器。
上傳時間： 2013-10-23
上傳用戶：GHF
蟲蟲下載站版權所有 京ICP備2021023401號-1
