USB接口控制器參考設(shè)計,xilinx提供VHDL代碼 usb xilinx vhdl
; This program is free software; you can redistribute it and/or modify
; it under the terms of the GNU General Public License as published by
; the Free Software Foundation; either version 2 of the License, or
; (at your option) any later version.
;
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with this program; if not, write to the Free Software
; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
This document provides practical, common guidelines for incorporating PCI Express interconnect
layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10-
layer or more server baseboard designs. Guidelines and constraints in this document are intended
for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI
Express devices located on the same baseboard (chip-to-chip routing) and interconnects between
a PCI Express device located “down” on the baseboard and a device located “up” on an add-in
card attached through a connector.
This document is intended to cover all major components of the physical interconnect including
design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card
edge-finger and connector considerations. The intent of the guidelines and examples is to help
ensure that good high-speed signal design practices are used and that the timing/jitter and
loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect.
However, while general physical guidelines and suggestions are given, they may not necessarily
guarantee adequate performance of the interconnect for all layouts and implementations.
Therefore, designers should consider modeling and simulation of the interconnect in order to
ensure compliance to all applicable specifications.
The document is composed of two main sections. The first section provides an overview of
general topology and interconnect guidelines. The second section concentrates on physical layout
constraints where bulleted items at the beginning of a topic highlight important constraints, while
the narrative that follows offers additional insight.
a Java program that reads a file containing instructions written in self-defined file (TPL in this case), and executes those instructions. This program should take the name of the TPL file as a command line parameter, and write its output to the console.
This code will be useful to you if you have tried using ADOCE, but never got anything to work. It is not meant to be integrated into any application, but rather it should be used for demonstrative purposes. It clearly shows the basics of how to use the technology.
Tug of War(A tug of war is to be arranged at the local office picnic. For the tug of war, the picnickers must be divided into two teams. Each person must be on one team or the other the number of people on the two teams must not differ by more than 1 the total weight of the people on each team should be as nearly equal as possible. The first line of input contains n the number of people at the picnic. n lines follow. The first line gives the weight of person 1 the second the weight of person 2 and so on. Each weight is an integer between 1 and 450. There are at most 100 people at the picnic. Your output will be a single line containing 2 numbers: the total weight of the people on one team, and the total weight of the people on the other team. If these numbers differ, give the lesser first. )
Lachesis an IRCRPG combat engine written in a combination of C and C++. The combat engine is being written for a specific RPG, but most of the project should be useful to IRCRPGs in general. It includes a native interface to the IRC protocol to allow it to act as an IRC bot, for such uses as dice rolling and acting as a remote-controlled client (RPG NPC perhaps).
Addressbook using double-linked list. This example shows the use of a double-linked list by implementing an addressbook for the console. It has features like inserting, searching(linear), sorting(bubble sort), deleting and load/save to a file. I wrote this during my study of Applied Computer Science so it s intended mainly for students who want to know about some advanced programming techniques in C. The Code was compiled with MSVC++ 6.0 but it should compile with any ANSI-compliant compiler.
The code assumes a two-dimensional computational domain with TMz polarization (i.e., non-zero field Ez, Hx, and Hy). The program is currently written so that the incident field always strikes the lower-left corner of the total-field region first. (If you want a different corner, that should be a fairly simple tweak to the code, but for now you ll have to make that tweak yourself.) I have attempted to provide copious comments in the code and hope that a knowledgeable C programmer can quickly map the approach as described in the paper to what is in the program.
The goal with this project was to make it possible for almost any mobile-phone to use ICQ and be able to communicate with other users!
One other goal with this project was to lower the GPRS-traffic in the phone and make the ICQ-ing cheaper.
A third goal was to make this service as easy to log-in to as possible. Anyone tried to fill a log-in screen with a WAP-browser should know what I mean.
With Wapmess all you have to do is to write your login-url ONCE and then bookmark it in your phone, to make it available fast. :)
In the ffuart.tar.gz it has one file.
The serial.c is the source codes of the FFUART as a console port, it should be put into the directory: /usr/src/linux/drivers/char/, and be compiled into the kernel.
