使用時鐘PLL的源同步系統時序分析一）回顧源同步時序計算Setup Margin = Min CLOCK Etch Delay – Max Data Etch Delay – Max Delay Skew – Setup TimeHold Margin = Min Data Etch Delay – Max CLOCK Etch Delay + Min Delay Skew + Data Rate – Hold Time下面解釋以上公式中各參數的意義：Etch Delay：與常說的飛行時間(Flight Time)意義相同，其值并不是從仿真直接得到，而是通過仿真結果的后處理得來。請看下面圖示：圖一為實際電路，激勵源從輸出端，經過互連到達接收端，傳輸延時如圖示Rmin，Rmax，Fmin，Fmax。圖二為對應輸出端的測試負載電路，測試負載延時如圖示Rising，Falling。通過這兩組值就可以計算得到Etch Delay 的最大和最小值。
上傳時間： 2013-11-05
上傳用戶：VRMMO
數字與模擬電路設計技巧IC與LSI的功能大幅提升使得高壓電路與電力電路除外，幾乎所有的電路都是由半導體組件所構成，雖然半導體組件高速、高頻化時會有EMI的困擾，不過為了充分發揮半導體組件應有的性能，電路板設計與封裝技術仍具有決定性的影響。 模擬與數字技術的融合由于IC與LSI半導體本身的高速化，同時為了使機器達到正常動作的目的，因此技術上的跨越競爭越來越激烈。雖然構成系統的電路未必有CLOCK設計，但是毫無疑問的是系統的可靠度是建立在電子組件的選用、封裝技術、電路設計與成本，以及如何防止噪訊的產生與噪訊外漏等綜合考慮。機器小型化、高速化、多功能化使得低頻/高頻、大功率信號/小功率信號、高輸出阻抗/低輸出阻抗、大電流/小電流、模擬/數字電路，經常出現在同一個高封裝密度電路板，設計者身處如此的環境必需面對前所未有的設計思維挑戰，例如高穩定性電路與吵雜(noisy)性電路為鄰時，如果未將噪訊入侵高穩定性電路的對策視為設計重點，事后反復的設計變更往往成為無解的夢魘。模擬電路與高速數字電路混合設計也是如此，假設微小模擬信號增幅后再將full scale 5V的模擬信號，利用10bit A/D轉換器轉換成數字信號，由于分割幅寬祇有4.9mV，因此要正確讀取該電壓level并非易事，結果造成10bit以上的A/D轉換器面臨無法順利運作的窘境。另一典型實例是使用示波器量測某數字電路基板兩點相隔10cm的ground電位，理論上ground電位應該是零，然而實際上卻可觀測到4.9mV數倍甚至數十倍的脈沖噪訊(pulse noise)，如果該電位差是由模擬與數字混合電路的grand所造成的話，要測得4.9 mV的信號根本是不可能的事情，也就是說為了使模擬與數字混合電路順利動作，必需在封裝與電路設計有相對的對策，尤其是數字電路switching時，ground vance noise不會入侵analogue ground的防護對策，同時還需充分檢討各電路產生的電流回路(route)與電流大小，依此結果排除各種可能的干擾因素。以上介紹的實例都是設計模擬與數字混合電路時經常遇到的瓶頸，如果是設計12bit以上A/D轉換器時，它的困難度會更加復雜。
上傳時間： 2013-11-16
上傳用戶：731140412
LAYOUT REPORT .............. 1 目錄.................. 1 1. PCB LAYOUT 術語解釋(TERMS)......... 2 2. Test Point : ATE 測試點供工廠ICT 測試治具使用............ 2 3. 基準點 (光學點) -for SMD:........... 4 4. 標記 (LABEL ING)......... 5 5. VIA HOLE PAD................. 5 6. PCB Layer 排列方式...... 5 7.零件佈置注意事項 (PLACEMENT NOTES)............... 5 8. PCB LAYOUT 設計............ 6 9. Transmission Line ( 傳輸線 )..... 8 10.General Guidelines – 跨Plane.. 8 11. General Guidelines – 繞線....... 9 12. General Guidelines – Damping Resistor. 10 13. General Guidelines - RJ45 to Transformer................. 10 14. CLOCK Routing Guideline........... 12 15. OSC & CRYSTAL Guideline........... 12 16. CPU
上傳時間： 2013-12-20
上傳用戶：康郎
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external CLOCK for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上傳時間： 2013-10-24
上傳用戶：wd450412225
TLC2543是TI公司的12位串行模數轉換器，使用開關電容逐次逼近技術完成A/D轉換過程。由于是串行輸入結構，能夠節省51系列單片機I/O資源；且價格適中，分辨率較高，因此在儀器儀表中有較為廣泛的應用。 TLC2543的特點 （1）12位分辯率A/D轉換器； （2）在工作溫度范圍內10μs轉換時間； （3）11個模擬輸入通道； （4）3路內置自測試方式； （5）采樣率為66kbps； （6）線性誤差±1LSBmax； （7）有轉換結束輸出EOC； （8）具有單、雙極性輸出； （9）可編程的MSB或LSB前導； （10）可編程輸出數據長度。 TLC2543的引腳排列及說明 TLC2543有兩種封裝形式：DB、DW或N封裝以及FN封裝，這兩種封裝的引腳排列如圖1，引腳說明見表1 TLC2543電路圖和程序欣賞 #include<reg52.h> #include<intrins.h> #define uchar unsigned char #define uint unsigned int sbit CLOCK=P1^0; sbit d_in=P1^1; sbit d_out=P1^2; sbit _cs=P1^3; uchar a1,b1,c1,d1; float sum,sum1; double sum_final1; double sum_final; uchar duan[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; uchar wei[]={0xf7,0xfb,0xfd,0xfe}; void delay(unsigned char b) //50us { unsigned char a; for(;b>0;b--) for(a=22;a>0;a--); } void display(uchar a,uchar b,uchar c,uchar d) { P0=duan[a]|0x80; P2=wei[0]; delay(5); P2=0xff; P0=duan[b]; P2=wei[1]; delay(5); P2=0xff; P0=duan[c]; P2=wei[2]; delay(5); P2=0xff; P0=duan[d]; P2=wei[3]; delay(5); P2=0xff; } uint read(uchar port) { uchar i,al=0,ah=0; unsigned long ad; CLOCK=0; _cs=0; port<<=4; for(i=0;i<4;i++) { d_in=port&0x80; CLOCK=1; CLOCK=0; port<<=1; } d_in=0; for(i=0;i<8;i++) { CLOCK=1; CLOCK=0; } _cs=1; delay(5); _cs=0; for(i=0;i<4;i++) { CLOCK=1; ah<<=1; if(d_out)ah|=0x01; CLOCK=0; } for(i=0;i<8;i++) { CLOCK=1; al<<=1; if(d_out) al|=0x01; CLOCK=0; } _cs=1; ad=(uint)ah; ad<<=8; ad|=al; return(ad); } void main() { uchar j; sum=0;sum1=0; sum_final=0; sum_final1=0; while(1) { for(j=0;j<128;j++) { sum1+=read(1); display(a1,b1,c1,d1); } sum=sum1/128; sum1=0; sum_final1=(sum/4095)*5; sum_final=sum_final1*1000; a1=(int)sum_final/1000; b1=(int)sum_final%1000/100; c1=(int)sum_final%1000%100/10; d1=(int)sum_final%10; display(a1,b1,c1,d1); } }
上傳時間： 2013-11-19
上傳用戶：shen1230
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System CLOCKs - Up to 25MIPS Throughput with 25MHz System CLOCK - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or CLOCK - Real-Time CLOCK Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
標簽： C8051F020
上傳時間： 2013-10-12
上傳用戶：lalalal
Designing read/write device (RWD) units for industrial RF-Identification applications is strongly facilitated by the NXP Semiconductors HITAG Reader Chip HTRC110. All needed function blocks, like the antenna driver, modulator demodulator and antenna diagnosis unit, are integrated in the HTRC110. Therefore only a minimum number of additional passive components are required for a complete RWD. This Application Note describes how to design an industrial RF-Identification system with the HTRC110. The major focus is dimensioning of the antenna, all other external components including CLOCK and power supply, as well as the demodulation principle and its implementatio
上傳時間： 2013-10-22
上傳用戶：zhengjian
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, CLOCK frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上傳時間： 2014-01-24
上傳用戶：xingisme
目錄： 1. Character Type Functions － 字符類型函數 2. Standard C Input/Output Functions － 標準輸入輸出函數 3. Standard Library Functions － 標準庫和內存分配函數 4. Mathematical Functions － 數學函數 5. String Functions － 字符串函數 6. BCD Conversion Functions － BCD 轉換函數 7. Memory Access Functions － 存儲器訪問函數 8. Delay Functions － 延時函數 9. LCD Functions － LCD函數 10. LCD Functions for displays with 4x40 characters － 4×40 字符型LCD函數 11. LCD Functions for displays connected in 8 bit memory mapped mode －以8 位外部存儲 器模式接口的LCD顯示函數 12. I2C Bus Functions － I2C 總線函數 13. National Semiconductor LM75 Temperature Sensor Functions － LM75 溫度傳感器函數 14. Dallas Semiconductor DS1621 Thermometer/Thermostat Functions － DS1621 溫度計函 數 15. Philips PCF8563 Real Time CLOCK Functions － PCF8563 實時時鐘函數 16. Philips PCF8583 Real Time CLOCK Functions － PCF8583 實時時鐘函數 17. Dallas Semiconductor DS1302 Real Time CLOCK Functions － DS1302 實時時鐘函數 18. Dallas Semiconductor DS1307 Real Time CLOCK Functions － DS1307 實時時鐘函數 19. 1 Wire Protocol Functions － 單線通訊協議函數 20. Dallas Semiconductor DS1820/DS1822 Temperature Sensors Functions － DS1820/1822 溫度傳感器函數 21. SPI Functions － SPI 函數 22. Power Management Functions － 電源管理函數 23. Gray Code Conversion Functions － 格雷碼轉換函數
上傳時間： 2013-10-22
上傳用戶：歸海惜雪
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects CLOCK chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上傳時間： 2013-10-15
上傳用戶：urgdil
